Home Up a Level Store Top Terms & Conds Search View Cart Checkout  Contact Us Login

Bike Lifts & Stands

Online Catalogue |  Bike Lifts & Stands

Page:  1  2   >   >>   View All (17) Page:  1  2   >   >>   View All (17)
1500Kg Ratchet Strap

1500Kg Ratchet Strap

These excellent quality hard wearing ratchet straps are manufactured to EN 12195-2:2001, so should not be confused with the nasty bright orange items commonly available from market stalls, fleabay etc. We tried the cheapo ones and nearly lost a restored 1977 Z1000A1 off the back of a trailer - never again.

To strap a bike down in a van or on trailer, we recommend using the Bike-It handlebar strap, with a ratchet strap either side, fully compressing the front forks. Any straps, whether used for lifting of securing should be looked after. Where possible try not to twist straps, don't allow them to become soaked with oil of other chemicals and whilst they are fine to be used outside, it is nor advisable to store in direct sunlight with the associated ultra violet rays.



Price: 6.21 (Excluding VAT at 20%)

Quantity:

Handle Bar Tie Down Support Strap

Handle Bar Tie Down Support Strap

These are an absolute must it you're transporting bikes in either vans or on trailers. They fit over the handlebars, allowing you to secure the bike by compressing the front suspension with ratchet straps. We've had ours for years and have used it to transport countless bikes, some very heavy lardy monsters like Harleys.




Price: 6.99 (Excluding VAT at 20%)

Quantity:

300Kg Motorcycle Scissor Stand

300Kg Motorcycle Scissor Stand

Scissor support stand suitable for use either on a motorcycle lift or on the floor.

Supplied with sliding pin carriers and three pairs of support pins.

Raise with a 22mm spanner/socket.

Low Pin Support Minimum Height: 180mm
Medium Pin Support Height: 200mm
High Pin Support Minimum Height: 220mm
Maximum Height: 335mm


Price: 111.97 (Excluding VAT at 20%)

Quantity:

BikeTek Sissor Lift Bike Jack

BikeTek Sissor Lift Bike Jack

This mini jack lift is so useful if you have a big bike lift, especially if you want to raise one or both of the wheels off the deck of the lift. It is particulary useful when working on Harleys, choppers of even metric cruisers. We have had this model in our workshop for years and it has been invaluable on so many occasions. It comes with a pair of cup extensions which are independently adjustable which can be very useful when lifting a bike with uneven lifting surfaces underneath. It has a 'tommy'bar but can also be operated with a socket as well. It can be used on the floor as well, but our days of grovelling around on the floor underneath bikes are long gone.


Price: 125.99 (Excluding VAT at 20%)

Quantity:

450KG Motorcycle Scissor Stand

450KG Motorcycle Scissor Stand

Scissor support stand suitable for use either on a motorcycle lift or on the floor.

Fitted with ball bearing rollers for smooth lifting and lowering.

Raise by hand or with sliding T-bar.

Supplied with non-slip platform cover for added load security.

Minimum Height: 85mm
Maximum Height: 365mm


Price: 99.99 (Excluding VAT at 20%)

Quantity:

Deluxe Folding Aluminium Bike Loading Ramps

Deluxe Folding Aluminium Bike Loading Ramps

These ramps are very nicely manufactured from lightweight extruded aluminium section. They are strong and durable to enable the safe loading of motorcycles into vans and trailers. For compact storage they fold into three. They have lightening holes in the cross members which not only help keep the weight down, but also help with tyre grip.

These ramps are available in either 230mm or 280mm width and are 1935mm long


Quantity:

Width

Quick Release Tie Down Anchors

Quick Release Tie Down Anchors

These tie down anchors have loads of uses. As bike benches rarely have enough, if any, tie down points, we always fit a number of these on our benches. Before these came on the market we used 'U' bolts, but they were always getting in the way when not in use. When not being used the tie on point is easily removed, leaving an unobtrusive anchor point. They can also used inthe back ov vans or in trailers to tie down bikes. Please be carefull not to ratchet against the quick release mechanism at an angle. These anchors are great but care must be used. If in any doubt feel free to e-mail or telephone us for advice on the safe use of this excelent product. The kit comes with mounting bolts, washers, nyloc nuts and two anchors points

Price: 16.79 (Excluding VAT at 20%)

Quantity:

Laser Front Wheel Chock

Laser Front Wheel Chock

We have tried lots of wheel chocks, both expensive and too cheap, and this product is the best we have tried. It's not the cheapest, but it is the easiest to use and is very well made. We have found that the soft rubber feet make it much easier to get the bike out when you're on your own. Ours lives in the van and never slides around when not in use.



Price: 86.69 (Excluding VAT at 20%)

Professional Rear Paddock Stand

Professional Rear Paddock Stand

This is a high quality Italian made professional stand, for use with bikes with standard swinging arms. We supply this with either a pair universal rubber adapters to grip under the swinging arm members or a pair of universal 'V' adapters that slot into the bobbins which can be fitted to the more modern bikes. The support height centres are 340mm from the ground. These come with four high impact plastic wheels with solid rubber tyres for maximum stability. Please state which adapters you want.

Price: 74.99 (Excluding VAT at 20%)

Quantity:

BikeLift Aluminium Swinging Arm Bobbins

BikeLift Aluminium Swinging Arm Bobbins

These bobbins are simply screwed into a modern bike swinging arm where they stay. Don't forget to put a drop of BondLoc B243 on the threads to halt corrosion and ensure they don't come loose. Then you simply hook the paddock stand into them to lift the bike for easy maintenance.

These are available in M6, M8, M10 & M12. Please select the size and colour you want from the menu.


Total Price: 8.60 (Excluding VAT at 20%)

Quantity:

SIze and Colour

Rear Paddock Stand for 2006-2007 Suzuki Bikes

Rear Paddock Stand for 2006-2007 Suzuki Bikes

This professional, Italian made stand is made in one piece specifically for 2006-2007 Suzuki models with centring bushings attached under the swinging arms and comes complete with the 'V' adapters. The centre height of the support adapters is 330mm.
3 week delivery - sorry


Price: 72.93 (Excluding VAT at 20%)

Lower Rear Paddock Stand

Lower Rear Paddock Stand

A number of bikes with a lower swing arm bobbin height require a non standard paddock stand.

It is perfect for a Kawasaki ZRX1200 - we know, we have one, even though it was made specifically for the Suzuki Hayabusa and B-Kings

Italian made, one piece, professional paddock stand. Centre heigh of support is 270mm from the ground.


Price: 72.93 (Excluding VAT at 20%)

Quantity:

Page:  1  2   >   >>   View All (17) Online Catalogue > Bike Lifts & Stands